When a flow has to be regulated rather than simply started and stopped, the globe valve is the reference design every other throttling valve is measured against. It has been around for well over a century and it is still the default body style for control valves in steam, water and chemical service. That is not habit. The geometry of a globe valve gives a stable, predictable relationship between stem position and flow, and it puts the high velocity, high wear zone on replaceable parts rather than on the body.
Why the globe body throttles well
In a globe valve the closure member, a plug or disc, moves perpendicular to the seat along the axis of the stem. Flow enters the body, turns to pass through the seat ring, then turns again to leave. The opening between plug and seat is an annulus whose area changes progressively with stem travel. Because the plug approaches the seat face on, nothing slides across the seating surface while the valve throttles, and the jet leaving the annulus discharges into the body cavity rather than along a sealing face.
Compare that with a gate valve, where the throttled jet runs straight across the seat faces, or a standard ball valve, where the seat edge meets the jet as soon as the ball cracks open. Both lose their shutoff when used to throttle. A globe valve is far more forgiving, and in a control valve the plug and seat ring are designed to be replaced together as a trim set without removing the body from the line.
The price of that control is pressure drop. Two changes of direction give a globe valve a much higher resistance coefficient than a gate or full bore ball valve of the same size, so the fully open loss is substantial. In throttling duty that hardly matters, since the valve is there to absorb pressure anyway. In isolation duty it is wasted pumping energy, which is why large globe valves are rarely chosen for plain on and off service.
Y pattern bodies reduce the loss by inclining seat and stem so the flow path is straighter, and they are common on high pressure feedwater and blowdown duties. Angle bodies turn the flow through ninety degrees and suit flashing, erosive and high pressure drop service, because the jet leaves the trim straight down the outlet pipe instead of hitting the body wall.
Flow under the plug or over it
A globe body carries a flow arrow, and in throttling service it matters which way the fluid passes the plug.
With flow under the plug, fluid enters below the seat and pushes up against the plug, so upstream pressure tends to open the valve. When the valve is shut, the packing sees only downstream pressure, which reduces stem leakage and makes repacking easier. Throttling is smooth because the plug is pushed away from the seat rather than drawn toward it. This is the usual arrangement for manual globe valves and most small control valves.
With flow over the plug, upstream pressure pushes the plug onto the seat. That helps shutoff and supports a fail closed action, but near the closed position the plug can be pulled suddenly onto the seat, the bathtub stopper effect, giving unstable control at low lift. Flow over the plug has legitimate uses on some large high pressure valves and on flashing duty, but it should be a deliberate choice, not an accident of installation.
Trim characteristic and where the valve should sit
The plug contour, or the shape of the ports in a cage, sets the inherent flow characteristic, the relationship between travel and flow coefficient at constant pressure drop. Three are common.
- Linear, where equal increments of travel give equal increments of flow coefficient. It suits systems where the valve takes most of the system pressure drop, such as level control on a vessel fed from a constant pressure header.
- Equal percentage, where each increment of travel changes the flow coefficient by the same percentage of its current value. It suits systems where the valve takes a small share of the total drop, because the installed characteristic straightens as more of the drop moves into the piping at higher flow. Most temperature and pressure loops use it.
- Quick opening, where most of the flow change happens early in the stroke. It belongs on on and off duty, not on fine control.
The inherent characteristic is not what the plant sees. The installed characteristic depends on how the system pressure drop redistributes between valve and piping as flow changes. A linear trim in a system dominated by pipe friction behaves much like a quick opening valve, and loop gain becomes extreme near closed. Size to the IEC 60534 or ISA 75 equations using the flow coefficient, Cv or Kv, at minimum, normal and maximum flow, and look at all three.
A well sized throttling globe valve sits in the middle part of its travel at normal flow, with room on either side. A valve running at a few per cent open spends its life with a high velocity jet across the seat, wire draws the seat ring and controls badly. A valve running near fully open has no authority left. The commonest error is oversizing, usually from margin added at every stage of the design, and the usual remedy is reduced trim in the same body.
Guiding, balancing and the actuator
In throttling service asymmetric flow forces push the plug sideways, so it needs guiding. Small valves use a top guided plug running in a single bushing. Larger and higher pressure valves use cage guiding, where the plug slides inside a cylindrical cage that also carries the flow ports. A cage stiffens the plug against vibration and lets the characteristic be changed by swapping the cage.
An unbalanced plug sees the full differential pressure across its seat area, and the actuator must overcome that force to stroke the valve and hold it steady. As size and pressure rise the force becomes large. A balanced plug has ports through it and a seal against the cage, so pressure acts on both faces and the net force is small. The trade off is a second leakage path at the balance seal, which limits the achievable shutoff. Pick unbalanced trim when tight shutoff comes first and the actuator can cope, and balanced trim when the force would otherwise demand an impractical actuator.
Packing friction matters more in throttling than in on and off service, because it causes stick slip and dead band. PTFE V ring packing suits most chemical duties within its temperature limit. Graphite is needed at high temperature and has to be loaded with care, since overloading it adds friction that a positioner then has to fight. On any throttling globe valve with an actuator, a positioner is almost always worth fitting.
Failures that point to a poor selection
Most throttling globe valve failures I investigate are selection errors rather than manufacturing defects. Wire drawn seats point to an oversized valve working near closed. Erosion of the body wall downstream of the seat points to flashing, or to an angle body that should have been used. Crackling noise and pitted trim point to cavitation, which needs staged trim or a different split of pressure drop. Stem leakage points to packing unsuited to the cycling rate or temperature. A globe valve selected with those four failures in mind will throttle accurately for many years, and when the trim finally wears, it comes out of the top of the body and the line stays where it is.